INTERGRANULAR CORROSION AND DUCTILE-BRITTLE TRANSITION BEHAVIOUR IN MARTENSITIC STAINLESS STEEL
DOI:
https://doi.org/10.51630/ijes.v2i3.23Keywords:
Martensitic Stainless Steel, Intergranular Corrosion, Ductile-Brittle TransitionAbstract
Material mechanical behavior is critical for both safety and economic considerations. Because engineering items are manufactured using appropriate grade materials, mechanical approval of the materials used must be completed before assembly. Petrochemicals, marine, and biomaterials are just a few of the industries that use stainless steel. Despite its extensive use, structural failure is still frequently caused by inadequate stainless steel type selection. As a result, dangerous conditions, resulting in personal harm or financial loss. Dangerous conditions is might result in accidents, resulting in personal injury or financial loss. Martensite stainless steel is a type of stainless steel with a high strength value but is brittle, necessitating careful handling. Intergranular corrosion, sensitization, tempering heat treatment, and the Ductile to Brittle Transition Temperature (DBTT) are topics still working on Martensite stainless steel for researchers.
Downloads
References
M. F. McGuire, Stainless Steels for Design Engineers. ASM International, 2008.
J. C. Lippold and D. J. Kotecki, Welding Metallurgy and Weldability of Stainless Steels. John Wiley & Son, 2005.
W. D. Callister and D. G. Rethwisch, Materials Science and Engineering: An Introduction, 9th Edition: Ninth Edition. John Wiley and Sons, Incorporated, 2013.
G. Coates and P. Cutler. (2009) Stainless Steels. Advanced Materials & Processes.
S. Kou, Welding Metallurgy. John Wiley & Sons, Inc, 2003.
K. Morshed-Behbahani, N. Zakerin, P. Najafisayar, and M. Pakshir, "A survey on the passivity of tempered AISI 420 martensitic stainless steel," Corrosion Science, vol. 183, 2021.
M. I. Ramli, A. B. Sulong, N. Muhamad, A. Muchtar, and A. Arifin, "Stainless steel 316L–hydroxyapatite composite via powder injection moulding: rheological and mechanical properties characterization," Materials Research Innovations, vol. 18, no. S6, pp. S6-100-S6-104, 2014.
A. Arifin, A. B. Sulong, N. Muhamad, J. Syarif, and M. I. Ramli, "Material processing of hydroxyapatite and titanium alloy (HA/Ti) composite as implant materials using powder metallurgy: A review," (in English), Materials & Design, vol. 55, no. 0, pp. 165-175, Mar 2014.
P. J. Hidalgo, "Pitting corrosion of martensitic cutlery steels," Surface Technology, vol. 10, no. 3, pp. 193-208, 1980.
S. S. M. Tavares, "Microstructure and Properties of New Super-Martensitic And
Super-Ferritic-Martensitic Stainless Steels," in Stainless Steel Microstructure, Mechanical Properties and Methods of Application, A. Pramanik and A. K. Basak, Eds.: Nova Science Publishers, Inc, 2015.
L. D. Barlow and M. Du Toit, "Effect of Austenitizing Heat Treatment on the Microstructure and Hardness of Martensitic Stainless Steel AISI 420," Journal of Materials Engineering and Performance, vol. 21, no. 7, pp. 1327-1336, 2011.
N. Alonso-Falleiros, M. Magri, and I. G. S. Falleiros, "Intergranular Corrosion in a Martensitic Stainless Steel Detected by Electrochemical Tests," Corrosion Engineering Science and Technology, vol. 55, no. 8, 1999.
N. Alonso-Falleiros, M. Magri, and I. G. S. Falleiros, "Intergranular Corrosion in a Martensitic Stainless Steel Detected by Electrochemical Tests," Corrosion, vol. 55, no. 8, pp. 769-778, 1999.
E. Bolli et al., "Cr Segregation and Impact Fracture in a Martensitic Stainless Steel," Coatings, vol. 10, no. 9, 2020.
A. Dalmau, C. Richard, and A. Igual – Muñoz, "Degradation mechanisms in martensitic stainless steels: Wear, corrosion and tribocorrosion appraisal," Tribology International, vol. 121, pp. 167-179, 2018.
A. N. Isfahany, H. Saghafian, and G. Borhani, "The effect of heat treatment on mechanical properties and corrosion behavior of AISI420 martensitic stainless steel," Journal of Alloys and Compounds, vol. 509, no. 9, pp. 3931-3936, 2011.
D. C. Moreira, H. C. Furtado, J. S. Buarque, B. R. Cardoso, B. Merlin, and D. D. C. Moreira, "Failure analysis of AISI 410 stainless-steel piston rod in spillway floodgate," Engineering Failure Analysis, vol. 97, pp. 506-517, 2019.
R. L. Klueh, "Analysis of swelling behaviour of ferritic/martensitic steels," Philosophical Magazine, vol. 98, no. 28, pp. 2618-2636, 2018.
M. D. Harris et al., "Revisiting (Some of) the Lasting Impacts of the Liberty Ships via a Metallurgical Analysis of Rivets from the SS "John W. Brown"," Jom, vol. 67, no. 12, pp. 2965-2975, 2015.
K. Kendall, "Cracks: a century of toughness," in Crack Control, 2021, pp. 1-29.
J. Lancaster, "The technical background," in Engineering Catastrophes, 2005, pp. 139-189.
J. S. Dubey, S. L. Wadekar, and J. K. Chakravartty, "Elevated temperature fracture toughness of AISI 403 martensitic stainless steel," Journal of Nuclear Materials, vol. 254, no. 2-3, pp. 271-274, 1998.
V. Dudko, J. Borisova, and R. Kaibyshev, "Ductile-Brittle Transition in Martensitic 12%Cr Steel," Acta Physica Polonica A, vol. 134, no. 3, pp. 649-652, 2018.
B.Sunil Kumar, VivekanandKain, and V. B, "Effect of Tempering Treatments on Microstructure and Intergranular Corrosion of 13wt% Cr Martensitic Stainless Steel," CORROSION, pp. 362–378, 2017.
V. Dudko, A. Belyakov, and R. Kaibyshev, "Evolution of Lath Substructure and Internal Stresses in a 9% Cr Steel during Creep," ISIJ International, vol. 57, no. 3, pp. 540-549, 2017.
O. Takahashi, Y. Shibui, P. G. Xu, S. Harjo, T. Suzuki, and Y. Tomota, "Microstructural Features and Ductile-Brittle Transition Behavior in Hot-Rolled Lean Duplex Stainless Steels," Quantum Beam Science, vol. 4, no. 1, 2020.
J. Chen, W.-n. Zhang, Z.-y. Liu, and G.-d. Wang, "The Role of Retained Austenite on the Mechanical Properties of a Low Carbon 3Mn-1.5Ni Steel," Metallurgical and Materials Transactions A, vol. 48, no. 12, pp. 5849-5859, 2017.
H. Godin, J.-D. Mithieux, C. Parrens, G. Badinier, M. Sennour, and A.-F. Gourgues-Lorenzon, "Effects of cooling path and resulting microstructure on the impact toughness of a hot stamping martensitic stainless steel," Materials Science and Engineering: A, vol. 742, pp. 597-607, 2019.
Y. J. Li et al., "A novel phase transition behavior during dynamic partitioning and analysis of retained austenite in quenched and partitioned steels," Materials Science and Engineering: A, vol. 710, pp. 181-191, 2018.
A. J. Cooper, N. I. Cooper, A. Bell, J. Dhers, and A. H. Sherry, "A Microstructural Study on the Observed Differences in Charpy Impact Behavior Between Hot Isostatically Pressed and Forged 304L and 316L Austenitic Stainless Steel," Metallurgical and Materials Transactions A, vol. 46, no. 11, pp. 5126-5138, 2015.
S. S. M. Tavares, H. F. Abreu, T. R. Strohaecker, M. B. Silva, and M. C. S. d. Macêdo, "Influence of Heat Treatments on the Impact Toughness of a Ti-stabilized 12%Cr Supermartensitic Stainless Steel," Materials Research, vol. 20, no. 2, pp. 469-473, 2017.
M. Mirzaee, A. Momeni, N. Aieni, and H. Keshmiri, "Effect of quenching and tempering on microstructure and mechanical properties of 410 and 410 Ni martensitic stainless steels," Journal of Materials Research, vol. 32, no. 3, pp. 687-696, 2017.
G. K. Bansal, V. Rajinikanth, C. Ghosh, V. C. Srivastava, M. Dutta, and S. Ghosh Chowdhury, "Effect of cooling rate on the evolution of microstructure and mechanical properties of nonisothermally partitioned steels," Materials Science and Engineering: A, vol. 788, 2020.
K. Zhang, M. Zhang, Z. Guo, N. Chen, and Y. Rong, "A new effect of retained austenite on ductility enhancement in high-strength quenching–partitioning–tempering martensitic steel," Materials Science and Engineering: A, vol. 528, no. 29-30, pp. 8486-8491, 2011.
M. K. El-Fawkhry, M. Eissa, A. Fathy, and T. Mattar, "Development of Maraging Steel with Retained Austenite in Martensite Matrix," Materials Today: Proceedings, vol. 2, pp. S711-S714, 2015.
L. Kučerová, H. Jirková, and B. Mašek, "Continuous Cooling of CMnSi TRIP Steel," Materials Today: Proceedings, vol. 2, pp. S677-S680, 2015.
B. Fu, W. Y. Yang, M. Y. Lu, Q. Feng, L. F. Li, and Z. Q. Sun, "Microstructure and mechanical properties of C–Mn–Al–Si hot-rolled TRIP steels with and without Nb based on dynamic transformation," Materials Science and Engineering: A, vol. 536, pp. 265-268, 2012.
J. Hu et al., "Ensuring combination of strength, ductility and toughness in medium-manganese steel through optimization of nano-scale metastable austenite," Materials Characterization, vol. 136, pp. 20-28, 2018.
Z. J. Xie, S. F. Yuan, W. H. Zhou, J. R. Yang, H. Guo, and C. J. Shang, "Stabilization of retained austenite by the two-step intercritical heat treatment and its effect on the toughness of a low alloyed steel," Materials & Design, vol. 59, pp. 193-198, 2014.
M. S. Anwar, S. A. Chandra, R. N. Hakim, S. Prifiharni, Miftah, and E. Mabruri, "High-temperature Oxidation Resistance of Martensitic Stainless Steel 13Cr3Mo3Ni-cast after Heat Treated," Materials Today: Proceedings, vol. 13, pp. 235-240, 2019.
X. P. Ma, L. J. Wang, C. M. Liu, and S. V. Subramanian, "Role of Nb in low interstitial 13Cr super martensitic stainless steel," Materials Science and Engineering: A, vol. 528, no. 22-23, pp. 6812-6818, 2011.
D. Ye, J. Li, W. Jiang, J. Su, and K. Zhao, "Effect of Cu addition on microstructure and mechanical properties of 15%Cr super martensitic stainless steel," Materials & Design, vol. 41, pp. 16-22, 2012.
A. Bojack, L. Zhao, P. F. Morris, and J. Sietsma, "In-situ determination of austenite and martensite formation in 13Cr6Ni2Mo supermartensitic stainless steel," Materials Characterization, vol. 71, pp. 77-86, 2012.
X. P. Ma, L. J. Wang, C. M. Liu, and S. V. Subramanian, "Microstructure and properties of 13Cr5Ni1Mo0.025Nb0.09V0.06N super martensitic stainless steel," Materials Science and Engineering: A, vol. 539, pp. 271-279, 2012.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Gunawan Gunawan, Amir Arifin
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
![](https://www.aps.or.id/journal/index.php/ijes/management/settings/<a rel="license" href="http:/creativecommons.org/licenses/by-nc-nd/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https:/i.creativecommons.org/l/by-nc-nd/4.0/88x31.png" /></a><br />This work is licensed under a <a rel="license" href="http:/creativecommons.org/licenses/by-nc-nd/4.0/">Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License</a>.)
